Asset deployment | Treon Knowledgebase

Treon Industrial Node X deployment strategy

Mon, 01 Jan 0001 00:00:00 +0000

Deploying the Treon Industrial Node X in an industrial environment is straightforward, but multiple factors need to be taken into consideration:

the installation location on the monitored asset.
the mounting methods.
surface and environmental temperatures.
hazardous areas.
the layout of the whole mesh network.

General product information

Treon Industrial Node X

Mounting interface: M30×2.0 adapter interface.
30 mm direct mounting surface.
Weight: 210g
Environmental: IP6K9K rating.
Temperature range: −40 to +85 °C operation temperature range.
Sensing: tri‑axial vibration (usable up to ~6.3 kHz depending on mounting), surface temperature −40 to +85 °C.

For more information, please see the Treon Industrial Node X datasheet.

Installation location

The aim is to pick an installation location on the asset that has the best measurable vibration and temperature reading for permanent monitoring of the asset and predictive maintenance.

As a general rule, mount the Treon Industrial Node X sensor as close to the bearing load zone as feasible.

Avoid installation on thin covers or guards or loosely fastened parts that can resonate, such as for example motor fan cover. Also avoid areas where other machine parts or on-location personnel have a high chance of getting into contact with the sensor.

Do not deploy the Treon Industrial Node X to high temperatures locations over 85 °C and any other locations that might lead to sub-optimal sensor readings, damage to the sensor, and reduced battery life-time.

Always consult the assets' product documentation of the asset before installing a sensor.

Read more about choosing the best installation location.

Mounting method

There are five recommended mounting methods for the Treon Industrial Node X:

Treon Bolt Mount Adapter mounting
Treon Orientation Adapter mounting
Treon Magnetic Glue Adapter for Flat Surface mounting
Treon Magnetic Glue Adapter for Curved Surface mounting
Direct glue mounting

Bolt mounting via the Treon Bolt Mount Adapter or the Treon Orientation Adapter are the most suitable solution for most assets.

Read our full documentation on mounting strategies for the Treon Industrial Node X.

Mesh network layout

When deploying your Treon solution, it is key to plan the Wirepas mesh network before the actual on-site installation.

The layout of the deployment environment and location of monitored assets will define the best placement for gateways and design of the whole mesh network. It is essential to plan the whole mesh network layout before the actual deployment, so all data is delivered from the sensor nodes to the Treon Connect instance smoothly.

Read our full article series on Wirepas mesh network strategies for the Treon Industrial Node X.

Treon Industrial Node X installation location

Mon, 01 Jan 0001 00:00:00 +0000

Installation location

The aim is to pick an installation location on the asset that has the best measurable vibration and temperature reading for predictive maintenance of the asset.

As a general rule, mount the Treon Industrial Node X as close to the bearing load zone as feasible.

Avoid placing the Treon Industrial Node X to high temperatures locations over 85 °C and any other locations that might lead to sub-optimal sensor readings,damage to the sensor, or reduced battery life-time.

Always consult the product documentation of the asset before installing a sensor.

Horizontal machines

For machines with horizontal alignment or installation we propose the sensor locations depicted in the graphics below. In most cases, these will lead to optimal sensor readings on a horizontal machine.

Please note that the bearing load zone is typically located on the bottom half of the bearing.

Vertical machines

For machines with vertical alignment or installation we propose the sensor locations depicted in the graphic below. In most cases, these will lead to optimal sensor readings on a vertical machine.

Node orientation and measurement directions

Align all Treon Industrial Node X sensors on the asset and across assets in the same direction whenever possible. Unified orientation helps analyzing the measurements as readings from sensor axis are directly comparable.

Align node axes as follows:
• Align one node axis to the assets horizontal direction
• Align one node axis to the assets vertical direction
• Align one node axis with the asset’s shaft direction

As a visual reference, use the Treon Industrial Node X’s safety‑screw opening which represents the node’s Z-axis.

Manual alignment of the node during installation requires a Treon Magnetic Glue Adapter for Flat Surface, Treon Magnetic Glue Adapter for Curved Surface or Treon Orientation Adapter. The Treon Bolt Mount Adapter does not allow axis rotation during installation or afterward.

It is recommended to always use at least one radial (vertical or horizontal) direction. Axial measurements should be taken at least in axial load carrying (thrust) bearing locations.

Mounting

Prefer bolt mounting and spot face drilling for best frequency response. For bolt mounting orientation adapter is recommended so that Node can be oriented properly.

Do not glue if there is a risk of damage to machinery in case the glue fails causing a sensor detachment.

Amount of Nodes

Preferably one Node per (key) bearing. If bearings are less than 25 cm (10 inch) apart, one sensor is sufficient to monitor both. This is valid for small motors, pumps, fans and gearboxes.

Good mounting practice

Example 1: Ideal sensor orientation on a horizontal machine.

The sensor node axes align with each other and to real world horizontal (Y), vertical (X) and axial (Z) directions. This helps when analyzing the data.

Example 2: Measurement locations on a large motor and overhung fan unit.
One sensor node is installed close to each of the bearings (two on motor and two on fan bearings housings). The node orientations are aligned, which makes sensor data analysis easier and enables comparization of sensor data across multiple sensors.

Example 3: Measurement locations on a large gearmotor.
Two sensor nodes are installed on the motor - one to the NDE (non-drive-end) and the other to the DE (drive-end). Two sensor are installed to gear - one near the input shaft and one near the output shaft.

Example 4: Good measurement locations marked on a small gearmotor.
Two sensor nodes can be considered sufficient for this asset. One sensor is installed to the motor (DE (drive-end) usually offer better mounting surfaces than NDE (non-drive-end)) and one sensor is installed near the gear output shaft.

Improper mounting locations

Mistake 1: Motor cooler fan cover mounting.
Installation of the sensor node on the motor cooler fan cover will predominantly pick up cooler fan vibrations which are not useful for asset condition monitoring.

Mistake 2: Motor cooler fin mounting.
Installation of the sensor node on the motor cooler fin will predominantly pick up cooler fin vibrations which are not useful for asset condition monitoring.

Mistake 3: Machine base mounting.
Installation directly on the machine base will likely be too far from the source of vibrations and only pick up dampened and mixed-up vibrations from the whole asset and not the parts to be monitored.

Mistake 4: Shaft cover mounting.
Installation on the shaft cover will likely be too far from the source of vibrations and only pick up dampened and mixed-up vibrations from the whole asset and not the parts to be monitored.

Troubleshooting

Error: Cannot identify the best mounting location.

Finding the ideal place to mount the Treon Industrial Node X to an asset might not be straight-forward and require some experience.
Carefully read our instructions above on choosing a location. Think which vibrations you want to measure for ideal monitoring of your asset.
If you are still unsure about the mounting location, consider a specialist's consultation with Treon.

Error: Sensor data does not match previous data.

When another sensor previously installed on the asset delivered different vibration or temperature data, this can have a multitude of reasons.
First, check that the Treon Industrial Node X is mounted in a location that picks up sensor data in a similar quality than your previous sensor in order to make it comparable.
Make sure the method the Treon Industrial Node X has been mounted with has been executed correctly and is suitable for the sensor location on the asset.
Check if both sensors have been aligned on the asset in a comparable way, and if sensor data from the same axes of the asset are compared.

Error: Sensor data does not match data from another sensor.

When another sensor currently installed on the asset delivers different vibration or temperature data, this can have a multitude of reasons.
Take into account that two sensors cannot be mounted in exactly the same location, so that there will always be a difference in the data. First, check that the Treon Industrial Node X is mounted in a location that picks up sensor data in a similar quality than your other sensor in order to make it comparable.
Make sure the method the Treon Industrial Node X has been mounted with has been executed correctly and is suitable for the sensor location on the asset.
Check if both sensors have been aligned on the asset in a comparable way, and if sensor data from the same axes of the asset is compared.

Mounting strategies for Treon Industrial Node X

Mon, 01 Jan 0001 00:00:00 +0000

Introduction

When mounting the Treon Industrial Node X to an asset, consider the location of the sensor and the contact between the sensor and the machine. The best location to attach the sensor depends on the machine and the monitored vibration source.

For best measurement quality, the contact surface on the machine should be:

completely flat: within 0.03 mm (1 mil = 1/1000th inch)
smooth: surface texture no greater than Ra 0.8 (32 microinches)
larger than the base of the Treon Industrial Node X

Installation methods

There are five recommended installation methods:

Treon Bolt Mount Adapter
Treon Orientation Adapter
Treon Magnetic Glue Adapter for Flat Surface
Treon Magnetic Glue Adapter for Curved Surface
Direct glue mounting

Mount type	Bonding	Minimum mounting surface diameter	Minimum thread hole depth	Curved surface	Allows manual orientation	Total height (node + adapter)
Treon Bolt Mount Adapter	M6x1 or M8x1,25 bolt	31,7 mm [1.25 in]	9 mm [0.35 in]	No	No	88 mm [3.46 in]
Treon Orientation Adapter	M6x1 or M8x1,25 bolt	25 mm [0.98 in]	9 mm [0.35 in]	No	Yes	91 mm [3.58 in]
Treon Magnetic Glue Adapter for Flat Surface	Glue	31,7 mm [1.24 in]	–	No	Yes	89 mm [3.50 in]
Treon Magnetic Glue Adapter for Curved Surface	Glue	33 mm [1.3 in]	–	Yes	Yes	89 mm [3.50 in]
Direct glue mounting	Glue	31,7 mm [1.25 in]	–	No	Yes	80 mm [3.15 in]

The four different adapters for Treon Industrial Node X have different installation surfaces:

Treon Bolt Mount Adapter, Treon Orientation Adapter,
Treon Magnetic Glue Adapter for Flat Surface, Treon Magnetic Glue Adapter for Curved Surface

Choosing the right installation method

Installation Method Comparison Table

Installation Method	Direct Glue Mounting	Bolt Mount Adapter	Orientation Adapter	Magnetic Glue Mount Adapter (Flat Surface)	Magnetic Glue Mount Adapter (Curved Surface)
Bonding	Glue	M6×1 or M8×1.25 bolt	M6×1 or M8×1.25 bolt	Glue	Glue
Minimum mounting surface diameter	31.7 mm (1.25 in)	31.7 mm (1.25 in)	25 mm (0.98 in)	31.7 mm (1.24 in)	33 mm (1.30 in)
Minimum thread hole depth	–	9 mm (0.35 in)	9 mm (0.35 in)	–	–
Total height (Node + adapter)	80 mm (3.15 in)	88 mm (3.46 in)	91 mm (3.58 in)	89 mm (3.50 in)	89 mm (3.50 in)
Curved surface	No	No	No	No	Yes
Uneven surface	No	No	No	No	Yes
Allows manual orientation	Yes	No	Yes	Yes	Yes
Frequency response (vibration)	Excellent	Excellent	Good	Good	Good
Temperature response (steady‑state)	Excellent	Good	Good	Medium	Medium
Fast temperature change response	Excellent	Good	Good	Medium	Medium
Affects magnetometer measurements	No	No	No	Yes	Yes

Surface preparation

For a proper and long-lasting installation of the Treon Industrial Node X, it is essential that the installation surface is as flat, smooth and clean as possible.

Ensure the machine contact surface is as flat as possible. Whenever it is possible to smoothen the installation surface, smoothen a surface larger than the base of the Treon Industrial Node X to ensure optimal mounting.

In case it is not possible to smoothen the installation surface, choose an installation method that will enable best possible sensor readings.

In case the mounting surface is covered by paint, consider removing the paint before installation of the sensor if possible.

Before installation of the Treon Industrial Node X, clean the surface to remove all dirt, grease and other contaminants.

Alignment

For accurate interpretation of the measurement data of all sensor axis, the centerline of Treon Industrial Node X is often aligned with the shaft of the rotating machine. This can be done by manually aligning the sensor with the shaft.

Manual alignment requires using the Treon Orientation Adapter or direct gluing. When mounting the sensor, align its axis directly toward drive or non- drive end of monitored machine using the orientation notch in the top window and the safety screw opening as visual guidelines

Installation with Treon Bolt Mount Adapter

The Treon Industrial Bolt Mount Adapter is directly attached to the asset’s surface. This minimizes the vibration transmission route for best measurement quality. Manual alignment of the Treon Industrial Node is not possible with this installation method.

Installation with Treon Bolt Mount Adapter requires a flat surface of 31.7 mm or 1.25 in diameter, and a hole for an M6x1 or M8x1,25 bolt with 9 mm or 0.35 in depth of threading.

Read the full article on installation without an adapter here.

Installation with Treon Orientation Adapter

Using a Treon Orientation Adapter has the benefits of the Treon Bolt Adapter with the additional benefit that it allows manual orientation of the Treon Industrial Node X during installation.

Installation with a Treon Orientation Adapter requires a flat surface of 25 mm or 0.98 in diameter, and a hole for an M6x1 or M8x1,25 bolt with 9 mm or 0.35 in depth of threading.

Read the full article on installation with a Treon Orientation Adapter here.

Treon Magnetic Glue Adapter for Flat Surface

Using the Treon Magnetic Glue Adapter for Flat Surface enables attaching the Treon Industrial Node to flat surfaces without drilling a hole for a bolt. It is possible to manually align the Treon Magnetic Glue Adapter for Flat Surface.

Installation with a Treon Magnetic Glue Adapter for Flat Surface requires a Treon Magnetic Glue Adapter for Flat Surface, suitable glue, and a surface area of minimum 31.7 mm or 1.24 in diameter.

Read the full article on installation with a Treon Magnetic Glue Adapter for Flat Surface here.

Treon Magnetic Glue Adapter for Curved Surface

Using the Treon Magnetic Glue Adapter for Curved Surface enables attaching the Treon Industrial Node to curved surfaces without drilling a hole for a bolt. It is possible to manually align the Treon Magnetic Glue Adapter for Curved Surface.

Installation with a Treon Magnetic Glue Adapter for Curved Surface requires a Treon Magnetic Glue Adapter for Curved Surface, suitable glue, and a surface area of at least 33 mm or 1.3 in diameter.

Read the full article on Installation with a Treon Magnetic Glue Adapter for Curved Surface here.

Direct glue mounting

Direct glue mounting allows installation of the Treon Industrial Node X to any flat or slightly uneven surfact directly without the use of an adapter.

Direct glue mounting requires suitable glue, and a surface area of at least 31.7 mm or 1.25 in diameter.

Read the full article on Direct glue mounting here.

Improper mounting techniques

Mistake 1: Wrong mounting location
Mounting should happen directly to the asset, not on parts extruding from the asset such as fan covers and cooling fins.

Mistake 2: Uneven mounting base
Mounting should happen on an even surface, with the Treon Industrial Node X mounted on a 90° angle to the surface.

<imgsrc="/media/nodex/nodex_mountingex7.png" width=“180”>

Mistake 3: Bolt-mounting without adapter
When you install the Treon Industrial Node X on the asset via a drill hole, make sure you use the right adapter:

Treon Bolt Mount Adapter or
Treon Orientation Adapter.

Installation with Treon Bolt Mount Adapter

Mon, 01 Jan 0001 00:00:00 +0000

Introduction - Treon Bolt Mount Adapter

With the Treon Bolt Mount Adapter, the Treon Industrial Node X is directly attached to the machine surface. This minimizes the vibration transmission route for best measurement quality. Manual alignment of the Industrial Node X is not possible with this installation method.

This installation method requires a flat surface of at least 31.7 mm or 1.25 in diameter, and a hole for an M6×1 or M8×1.25 bolt with at least 9 mm or 0.35 in depth of threading.

Applies to: Treon Industrial Node X
Adapter: Treon Bolt Mount Adapter
Use when: You can tap/drill a mounting hole on a completely flat, smooth surface and manual alignment is not necessary.

Specifications

Parameter	Value
Bonding	M6×1 or M8×1.25 bolt
Minimum mounting surface diameter	31.7 mm (1.25 in)
Minimum thread hole depth	9 mm (0.35 in)
Total height (Node + adapter)	88 mm (3.46 in)
Curved surface	No
Uneven surface	No
Allows manual orientation	No
Frequency response (vibration)	Excellent
Temperature response (steady‑state)	Good
Fast temperature change response	Good
Affects magnetometer measurements	No

Requirements

For this installation method you will need:

Treon Industrial Node X.
Treon Bolt Mount Adapter.
Tap/drill M6×1 or M8×1.25 bolt of minimum 9 mm or 0.35 in depth.
Torque wrench capable of applying 20 Nm.
Cleaning materials (degreaser/isopropyl alcohol, lint‑free wipes).
Personal protective equipment (PPE) as per site rules.

Safety & Preparation

Isolate an/or turn off the asset and other equipment in close proximity if required by your site procedures.
Select a flat, smooth area larger than the sensor base close to the measurement point and away from resonant/loose parts.
Clean the surface thoroughly; remove paint, rust, oil, and debris.
Verify there is sufficient thickness in the asset’s material for the tapped hole.

Step-by-step installation guide

Step 1: Drill mounting hole

Start with carefully drilling an M6×1 or M8×1.25 hole into the machine surface at the location you have chosen for the measurements. Please consider carefully where you drill the hole. If you are unsure, please consult the manual of the machine or the manufacturer.

Be sure to drill the hole with the correct alignment to the machine. For most uses, an exact angle of 90° to the plane will be the right choice.

The minimum required thread hole depth to drill is 9 mm or 0.35 in.

Step 2: Clean the surface

After drilling, clean the machine surface thoroughly.

Step 3: Attach mounting bolt to adapter

Attach the mounting bolt to the Treon Bolt Adapter by carefully screwing it in with a screwdriver. Choose the M6×1 bolt if you drilled an M6 hole and the M8×1.25 bolt if you drilled an M8 hole.

Step 4: Tighten adapter to node

Place the Treon Bolt Adapter with the attached mounting bolt on the Treon Industrial Node X and carefully screw it in.

Use a socket wrenches to tighten the connection.

Step 5: Attach to machinery

Now screw the Treon Industrial Node X with attached Treon Bolt Adapter into the M6 or M8 hole on the asset’s surface.

Optionally a threadlocker can be used if needed to secure the device in place.

Step 6: Tighten

Now set your torque wrench with a spanner size of 34 mm to a tightness of 20 Nm (Newton metres) and carefully tighten the Treon Industrial Node X to the machine.

Verification

Confirm axis alignment marks match the intended directions.
Run a quick measurement and validate expected directional sensitivity.

The Treon Industrial Node X is now fully installed!

Troubleshooting

Error: The surface has paint.

If possible, remove all paint from the asset's surface. Make sure to consult the asset manufacturer's manual or contact the manufacturer directly if unsure.

Error: The asset cannot be turned off.

In case the asset cannot be turned off for installation of the Treon Industrial Node X, please proceed with caution and take all safety protocols at the deployment site into account.

Error: Cannot drill hole

In case it is not possible to drill an M6 or M8 hole with 9mm depth, please choose another installation method.

Error: I over tightened the node.

Cannot be overtightened?

Error: The asset was damaged.

If at any point it seems like the asset was damaged during the installation process, please consult the machine's repair manual or contact the manufacturer for further instructions on how to conduct the repair.

Disclaimer

Treon is not responsible for any damage, injury, or malfunction resulting from the installation or use of the Treon Industrial Node X.

Installation must be performed by qualified personnel.

Any issues arising from incorrect installation, improper handling, or use outside the specified guidelines are the sole responsibility of the installer or end user.

Installation with Treon Orientation Adapter

Mon, 01 Jan 0001 00:00:00 +0000

Introduction

With the Orientation Adapter, the Treon Industrial Node X is attached to the machine surface using a threaded mounting hole. The adapter enables manual alignment, allowing the measurement axes to be oriented as needed for the monitored equipment.

This installation method requires a flat surface of at least 25 mm (0.98 in) in diameter, and a threaded hole for an M6×1 or M8×1.25 bolt with a minimum depth of 9 mm (0.35 in). For best measurement performance, the adapter should be tightened to approximately 20 Nm to ensure firm mechanical coupling.

Applies to: Treon Industrial Node X
Adapter: Treon Orientation Adapter
Use when: You need to align the measurement axes and have a threaded mounting hole on a flat surface.

Specifications

Parameter	Value
Bonding	M6×1 or M8×1.25 bolt
Minimum mounting surface diameter	25 mm (0.98 in)
Minimum thread hole depth	9 mm (0.35 in)
Total height (Node + adapter)	91 mm (3.58 in)
Curved surface	No
Uneven surface	No
Allows manual orientation	Yes
Frequency response (vibration)	Good
Temperature response (steady‑state)	Good
Fast temperature change response	Good
Affects magnetometer measurements	No

Requirements

For this installation method you will need:

Treon Industrial Node X.
Treon Orientation Adapter.
Tap/drill M6×1 or M8×1.25 bolt hole with minimum 9 mm (0.35 in) thread depth.
Torque wrench capable of applying 20 Nm.
Cleaning materials (degreaser/isopropyl alcohol, lint‑free wipes).
Personal protective equipment (PPE) as per site rules.

Safety & Preparation

Isolate an/or turn off the asset and other equipment in close proximity if required by your site procedures.
Select a flat, smooth area larger than the sensor base close to the measurement point and away from resonant/loose parts.
Clean the surface thoroughly; remove paint, rust, oil, and debris.
Verify there is sufficient thickness in the asset’s material for the tapped hole.

Step-by-step installation guide

Step 1: Drill mounting hole

Be sure to drill the hole with the correct alignment to the machine. For most uses, an exact angle of 90° to the plane will be the right choice.

The minimum required thread hole depth to drill is 9 mm or 0.35 in.

Step 2: Clean the surface

After drilling, clean the machine surface thoroughly.

Step 3: Attach mounting bolt to adapter

Attach the mounting bolt to the Treon Bolt Adapter. Choose the M6×1 bolt if you drilled an M6 hole and the M8×1.25 bolt if you drilled an M8 hole.

Place hex key to hex socket on the top side of the adapter and tighten bolt wit a screwdriver.

Step 4: Attach orientation adapter to orientation nut

Slide the orientation adapter to the orientation nut.

Step 5: Mount adapter on asset

Place the assembly on the mounting hole on your asset. Tighten firmly with a hex key.

Step 6: Attach adapter to asset

Now install the Treon Orientation Adapter in the bolt hole on the cleaned asset’s surface.

Step 7: Install node on adapter

Place the Treon Industrial Node X on the mounted adapter. Screw nut to the Node X but do not tighten.

Step 8: Alignment

Rotate the node to desired orientation to align the axes.

Tighten the connection with a spanner size 34 mm and a torque wrench set to exactly 20 Nm.

Verification

Confirm axis alignment marks match the intended directions.
Run a quick measurement and validate expected directional sensitivity.

The Treon Industrial Node X is now fully installed!

Troubleshooting

Error: The surface has paint.

If possible, remove all paint from the asset's surface. Make sure to consult the asset manufacturer's manual or contact the manufacturer directly if unsure.

Error: The asset cannot be turned off.

In case the asset cannot be turned off for installation of the Treon Industrial Node X, please proceed with caution and take all safety protocols at the deployment site into account.

Error: Cannot drill hole

In case it is not possible to drill an M6 or M8 hole with 9mm depth, please choose another installation method.

Error: I over tightened the node.

Cannot be overtightened?

Error: The asset was damaged.

Disclaimer

Treon is not responsible for any damage, injury, or malfunction resulting from the installation or use of the Treon Industrial Node X.

Installation must be performed by qualified personnel.

Any issues arising from incorrect installation, improper handling, or use outside the specified guidelines are the sole responsibility of the installer or end user.

Installation with Treon Magnetic Glue Adapter for Flat Surface

Mon, 01 Jan 0001 00:00:00 +0000

Introduction

With the Treon Magnetic Glue Mount Adapter for Flat Surface, the Treon Industrial Node X is glued to the equipment while the magnet temporarily holds the sensor in place during adhesive curing. This enables easy positioning and manual orientation prior to final bonding. After curing, the magnet is not responsible for holding the sensor in operation.

This installation method requires a flat, smooth surface with a minimum diameter of 31.7 mm (1.24 in). Magnetic adapters should not be used when measuring magnetic fields, as the magnet may interfere with the readings. Magnets are intended only as temporary support during installation.

Applies to: Treon Industrial Node X
Adapter: Treon Magnetic Glue Mount Adapter for Flat Surface
Use when: You need manual orientation and easy placement on a flat surface without drilling.

Specifications

Parameter	Value
Bonding	Glue
Minimum mounting surface diameter	31.7 mm (1.24 in)
Minimum thread hole depth	–
Total height (Node + adapter)	89 mm (3.50 in)
Curved surface	No
Uneven surface	No
Allows manual orientation	Yes
Frequency response (vibration)	Good
Temperature response (steady‑state)	Medium
Fast temperature change response	Medium
Affects magnetometer measurements	Yes

Requirements

For this installation method you will need:

Treon Industrial Node X.
Treon Magnetic Glue Mount Adapter for Flat Surface.
Flat mounting surface of at least 31.7 mm (1.24 in) diameter.
Industrial‑grade glue or epoxy suitable for metal bonding.
Cleaning materials (degreaser/isopropyl alcohol, lint‑free wipes).
Personal protective equipment (PPE) as per site rules.

Note: Magnets only hold the adapter during curing—final fixation depends on glue.

Step-by-step installation guide

Step 1: Clean the surface

Clean the mounting surface on the asset thoroughly.

Step 2: Attach adapter to node

Take the Treon Magnetic Glue Mount Adapter for Flat Surface, place it on the Treon Industrial Node X. Carefully screw the adapter on to the node.

Tighten the connection with a spanner size 34 mm and a torque wrench to 20 Nm.

Step 3: Apply glue to surface

Choose an appropriate glue like the Loctite HY 4090. Follow closely the instructions that come with the glue!

Apply the glue to the mounting area on the asset. The mounting area needs to be a minumum of 31.7 mm (1.24 in) in diameter.

Step 4: Place node on asset

Place the Treon Industrial Node X in the desired orientation on the area where you applied the glue. Make sure the magnet holds the node in place to secure the glue adhesion. Wait for the glue to dry.

Verification

Confirm axis alignment marks match the intended directions.
Run a quick measurement and validate expected directional sensitivity.

The Treon Industrial Node X is now fully installed!

Troubleshooting

Error: The surface has paint.

If possible, remove all paint from the asset's surface. Make sure to consult the asset manufacturer's manual or contact the manufacturer directly if unsure.

Error: The asset cannot be turned off.

In case the asset cannot be turned off for installation of the Treon Industrial Node X, please proceed with caution and take all safety protocols at the deployment site into account.

Error: Glue does not dry or hold.

Choose an appropriate glue such as the Loctite HY 4090 and follow closely the instructions that come with the glue.

Error: The asset was damaged.

Disclaimer

Treon is not responsible for any damage, injury, or malfunction resulting from the installation or use of the Treon Industrial Node X.

Installation must be performed by qualified personnel.

Any issues arising from incorrect installation, improper handling, or use outside the specified guidelines are the sole responsibility of the installer or end user.

Installation with Treon Magnetic Glue Adapter for Curved Surface

Mon, 01 Jan 0001 00:00:00 +0000

Introduction

With the Treon Magnetic Glue Mount Adapter for Curved Surface, the Treon Industrial Node X can be installed on slightly curved or uneven mounting surfaces. The adapter compensates for curvature and allows the node to be correctly positioned and manually oriented before the adhesive cures. The magnet temporarily supports the sensor during curing but is not intended for long‑term retention.

This installation method requires a curved mounting area of at least 33 mm (1.30 in) diameter. Magnetic adapters should not be used when measuring magnetic fields, because the magnet can interfere with the sensor’s magnetometer.

Applies to: Treon Industrial Node X
Adapter: Treon Magnetic Glue Mount Adapter for Curved Surface Use when: The surface is curved or slightly uneven, drilling is not possible, and manual orientation is required.

Specifications

Parameter	Value
Bonding	Glue
Minimum mounting surface diameter	33 mm (1.30 in)
Minimum thread hole depth	–
Total height (Node + adapter)	89 mm (3.50 in)
Curved surface	Yes
Uneven surface	Yes
Allows manual orientation	Yes
Frequency response (vibration)	Good
Temperature response (steady‑state)	Medium
Fast temperature change response	Medium
Affects magnetometer measurements	Yes

Requirements

For this installation method you will need:

Treon Industrial Node X.
Treon Magnetic Glue Mount Adapter for Curved Surface.
Slightly curved mounting surface of at least 33 mm (1.30 in) diameter.
Industrial‑grade glue or epoxy suitable for metal bonding.
Cleaning materials (degreaser/isopropyl alcohol, lint‑free wipes).
Personal protective equipment (PPE) as per site rules.

Note: Magnets must not be used for long‑term retention and are not recommended for magnetic field measurements.

Step-by-step installation guide

Step 1: Clean the surface

Clean the mounting surface on the asset thoroughly.

Step 2: Attach adapter to node

Take the Treon Magnetic Glue Mount Adapter for Curved Surface, place it on the Treon Industrial Node X. Carefully screw the adapter on to the node.

Tighten the connection with a spanner size 34 mm and a torque wrench to 20 Nm.

Step 3: Apply glue to surface

Choose an appropriate glue like the Loctite HY 4090. Follow closely the instructions that come with the glue!

Apply the glue to the mounting area on the asset. The mounting area needs to be a minumum of 33 mm (1.30 in) in diameter.

Step 4: Place node on asset

Verification

Confirm axis alignment marks match the intended directions.
Run a quick measurement and validate expected directional sensitivity.

The Treon Industrial Node X is now fully installed!

Troubleshooting

Error: The surface has paint.

If possible, remove all paint from the asset's surface. Make sure to consult the asset manufacturer's manual or contact the manufacturer directly if unsure.

Error: The asset cannot be turned off.

In case the asset cannot be turned off for installation of the Treon Industrial Node X, please proceed with caution and take all safety protocols at the deployment site into account.

Error: Glue does not dry or hold.

Choose an appropriate glue such as the Loctite HY 4090 and follow closely the instructions that come with the glue.

Error: The asset was damaged.

Disclaimer

Treon is not responsible for any damage, injury, or malfunction resulting from the installation or use of the Treon Industrial Node X.

Installation must be performed by qualified personnel.

Any issues arising from incorrect installation, improper handling, or use outside the specified guidelines are the sole responsibility of the installer or end user.

Installation with Direct glue mounting

Mon, 01 Jan 0001 00:00:00 +0000

Introduction

With the Direct Glue Mounting method, the Treon Industrial Node X is attached directly to the machine surface using glue. This provides the shortest possible vibration transmission path, delivering excellent measurement quality. Manual alignment of the Industrial Node X is possible before the adhesive cures, allowing the sensor to be oriented correctly for the application.

This installation method requires a completely flat and smooth surface with a minimum diameter of 31.7 mm (1.25 in). It is ideal for situations where drilling or tapping holes is not feasible. For best results, the node should be pressed firmly onto the surface until the glue or epoxy cures.

Applies to: Treon Industrial Node X
Adapter: None (direct bonding)
Use when: The surface is flat and smooth, drilling is not possible, and optimal vibration performance is required.

Specifications

Parameter	Value
Bonding	Glue
Minimum mounting surface diameter	31.7 mm (1.25 in)
Minimum thread hole depth	–
Total height (Node + adapter)	80 mm (3.15 in)
Curved surface	No
Uneven surface	No
Allows manual orientation	Yes
Frequency response (vibration)	Excellent
Temperature response (steady‑state)	Excellent
Fast temperature change response	Excellent
Affects magnetometer measurements	No

Requirements

Requirements – Direct Glue Mounting

For this installation method you will need:

Treon Industrial Node X.
Clean, flat mounting surface (minimum 31.7 mm / 1.25 in diameter).
Industrial‑grade glue or epoxy (e.g., Loctite 4090 or equivalent).
Cleaning materials (degreaser/isopropyl alcohol, lint‑free wipes).
Clamps or fixtures to hold the node in position while adhesive cures (optional).
Personal protective equipment (PPE) as per site rules.

Step 1: Clean the surface

Clean the machine surface thoroughly.

Step 2: Apply glue

Choose an appropriate glue like the Loctite HY 4090. Follow closely the instructions that come with the glue!

Apply the glue to the mounting area on the asset. The mounting area needs to be a minumum of 31.7 mm (1.25 in) in diameter.

Step 3: Place node on asset

Place the Treon Industrial Node X in the desired orientation on the area where you applied the glue. Hold it in place to secure glue adhesion.

Verification

Confirm axis alignment marks match the intended directions.
Run a quick measurement and validate expected directional sensitivity.

The Treon Industrial Node X is now fully installed!

Troubleshooting

Error: The surface has paint.

If possible, remove all paint from the asset's surface. Make sure to consult the asset manufacturer's manual or contact the manufacturer directly if unsure.

Error: The asset cannot be turned off.

In case the asset cannot be turned off for installation of the Treon Industrial Node X, please proceed with caution and take all safety protocols at the deployment site into account.

Error: Glue does not dry or hold.

Choose an appropriate glue such as the Loctite HY 4090 and follow closely the instructions that come with the glue.

Error: The asset was damaged.

Disclaimer

Treon is not responsible for any damage, injury, or malfunction resulting from the installation or use of the Treon Industrial Node X.

Installation must be performed by qualified personnel.

Any issues arising from incorrect installation, improper handling, or use outside the specified guidelines are the sole responsibility of the installer or end user.

Treon Industrial Node X activating

Mon, 01 Jan 0001 00:00:00 +0000

After installation, the Treon Industrial Node X needs to be turned on.

Please note that we recommend first testing the Treon Gateway and all Treon Industrial Node X sensors before actual deployment. This way you make sure that all nodes connect to the gateway, and the gateway delivers data to your Treon Connect instance.

This means that after deploying the Treon Industrial Node X sensors, they might already be turned on.

Checking the node status

To check if the Treon Industrial Node X is turned on, follow these steps:

Press the power button briefly.
If the status light turns green, the sensor is connected.

CONNECTED If the status light turns red, the sensor is not yet connected.

NOT CONNECTED

In case the sensor is not connected, the Gateway has been powered on, both sensor and Gateway are configured to same network and the sensor has had time to establish the connection, the sensor may be too far from the gateway or surroundings are blocking the radio connection. In either case, the gateway needs to be moved closer to the sensor or an additional routing sensor can be added between the sensor and the gateway to help routing the data.

Please note that to press the button or view the led, the top cap of the sensor needs to be removed. You can also check if the sensor is connected to a Gateway by

Activating the node

The Treon Industrial Node X can be powered on by two ways:

a. Bring an NFC field (such as in a smartphone) to the proximity of the sensor.

b. Press and hold the power button until the status light turns green.

Deactivating the node

To switch off the Treon Industrial Node X, press the power button until the status light turns red, then let go of the button.

The sensor serial number and a QR code including serial number are printed on the base of the sensor.

You can also use an NFC reader, such as NFC-enabled mobile phone to read the identification number: switch on NFC on the reader and touch the left side of the of the sensor with the reader.